Made-to-Measure 2-Way Y Splitters for Dust Extraction

A Y splitter divides one dust-extraction duct into two branches, so a single extractor or run can feed two machines or two pickup points. The smooth Y (wye) shape splits the airflow at a shallow angle, so it flows better and loses less suction than a sharp T-piece.

ProFlow Y splitters are made to measure - 3D-printed to the exact inlet and outlet bores your pipework needs, with the branch angle and port lengths you choose. Configure one in your browser, see it in 3D, and get a live price. UK-made and dispatched fast.

Also known as: Y piece · wye fitting · 2-way splitter · dust extraction Y connector · ducting Y branch · Y junction · hose splitter

ProFlow made-to-measure 2-way Y splitter for dust extraction ducting

What is a Y splitter used for?

A Y splitter is how you run two machines or pickup points from one length of ducting. Instead of a separate hose back to the extractor for every tool, you branch the duct once and take a leg to each:

  • Feed two machines from a single extractor or drop
  • Split a main run into two branches
  • Combine two pickups into one duct (it works both ways round)
  • Keep the airflow smooth - the shallow Y angle loses less suction than a right-angle T

Pair it with a blast gate on each leg and you can shut off the branch you're not using, so all the suction goes to the machine in use.

Made to measure: size the inlet and both outlets

Set the inlet bore and each outlet bore to match your pipe or hose, anywhere from 20 mm to 210 mm. The outlets can match the inlet or step down to smaller branches, so the same part doubles as a reducing splitter - no adapters, no mismatched joints, no leaks.

Need a 100 mm inlet splitting to two 63 mm branches? Just set the three diameters and we make it.

Set the branch angle and port lengths

Choose how far the two outlets splay apart, from a tight 20° for the smoothest, lowest-loss branch up to a wide 45° when the two machines sit further apart. Then set the port lengths so each leg reaches exactly where it needs to - matched, or sized independently.

Add a hose bead for flexible hose & ducting

Turn on the hose bead option and the inlet and outlets get a raised retaining ridge, so flexible hose pushes on and grips, with a jubilee clip seating neatly behind the bead. The inlet and outlets are set independently, so the Y joins straight to flexible dust hose or rigid pipe without a separate connector.

Splits or combines, low-loss either way

Air flows just as happily both ways through a Y, so the same part splits one duct into two or merges two pickups into one. The smooth wye transition means less turbulence and less lost suction than a boxy T-junction, so the machine on the end still pulls hard.

How it works

  1. You configure it - set the inlet and outlet bores, branch angle and options in the live 3D designer and watch the price update.
  2. We make it - 3D-printed to order in the UK to your exact spec, with speedy delivery throughout the UK.

Frequently asked questions

What size Y splitters can you make? +

Any bore from 20 mm to 210 mm, and you set the inlet and both outlets separately, so it can split into equal branches or step down to smaller ones. Common sizes like 63 mm, 100 mm (4 inch) and 150 mm are all just a setting.

Can I split to two different sizes? +

Yes. The two outlets are sized independently and can be smaller than the inlet, so one Y can feed two different machines or step a main run down into branches.

Can I connect flexible hose to a Y splitter? +

Yes - switch on the hose bead option and each port gets a retaining ridge that grips flexible dust hose securely. You can set the inlet and outlets independently to match hose or rigid pipe.

Does a Y splitter lose suction? +

Every branch costs a little airflow, but the smooth Y (wye) shape loses far less than a sharp T-piece. For the best results, fit a blast gate on each leg and only open the branch you're using.

What material are ProFlow Y splitters made from? +

They're 3D-printed to order in durable PET-G plastic, made in the UK, with a wall thickness you can set for lighter or heavier-duty use.

Related parts

Configure your 2-Way Y Splitter

Set your exact dimensions and options in the live 3D designer, see the price instantly, and we'll 3D-print it to order.

Open the designer